Evaporative cooler hook up

evaporative cooler hook up

How do you connect a water line to an evaporative cooler?

You then use the compression fitting in the kit to connect the water line to the needle valve. The needle valve is important because it allows you use of the faucet when you have to turn off water to the cooler. Rooftop evaporative coolers use more water than side-mounted units, so they are typically serviced by a 1/2-inch water line.

What do you need to set up an evaporative cooler?

Theres a good chance you have everything you need to set up a primitive evaporative cooler right at hand: a fan, a shallow container, and some water. Over at the project blog of Michael Colombo, Push the Other Button, he details his experiment in cooling his home in New York using evaporative cooling:

How does an evaporative cooler work?

This is exactly what happens in an evaporative cooler. Water is pumped up and poured onto a specialized cooling pad that has warm air blown through it by a high-powered fan.

How do you hook up a water cooler to a roof?

Once you have roughed-in the wiring and water line to the attic, simply pull across them across the attic space to your roof jack next to the cooler. Use 1/4 copper (preferable) or 1/4 plastic tubing. 1/4 pex may also be used, but takes special tools to prepare the joints. Make sure that the water line is not touching the flue.

How to install evaporative cooler water line installation?

Evaporative Cooler Water Line Installation Instructions. 1 Step 1. Turn the water off to the existing water valve before removing the valve to replace it with one that has a 1/4 inch port for the tubing. 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5. More items

How do you connect an evaporative cooler to a faucet?

You replace your existing faucet with the evaporative cooler faucet and screw the needle valve into the 1/8-inch outlet. You then use the compression fitting in the kit to connect the water line to the needle valve. The needle valve is important because it allows you use of the faucet when you have to turn off water to the cooler.

How do you hook up a water cooler to plumbing?

Connect the line to the 1/2- or 3/4-inch plumbing pipe closest to the cooler by installing a tee and running the cooler line off the tee. Run the cooler line indoors or outdoors from the point of connection to the cooler.

How to drain a swamp cooler water line?

The procedures of draining your swamp cooler water line are as follows: Switch off the direct evaporative fleet’s water supply source. Empty your swamp cooler water line if at all feasible. It is dependent on the model of the unit and how it is installed in your house.

Can you hook a swamp cooler to the roof?

If you do, youll need to replace the plastic sleeves with brass sleeves during your installation. Technically, you can hook a rooftop swamp cooler to a water supply line in the same way you would one mounted on the ground or in a window. However, you may have a long way to go from the roof to the ground and then to a water supply.

How do you run a water cooler on a roof?

Run the cooler line indoors or outdoors from the point of connection to the cooler. The easiest way to do this is often to run in through interior walls to the roof and poke a small hole for it directly underneath the cooler.

How do you hook up a water cooler to plumbing?

Connect the line to the 1/2- or 3/4-inch plumbing pipe closest to the cooler by installing a tee and running the cooler line off the tee. Run the cooler line indoors or outdoors from the point of connection to the cooler.

How do you attach a cooling collar to a roof?

Fit the collar into the port on the side of the cooler with the section of duct extending horizontally above the duct-riser at the roof. Install several wooden blocks below the section of duct to hold it horizontally. Fit one end of a 90-degree sheet-metal elbow onto the end of another 24-inch-long section of duct and tape the connection.

Related posts: